No subject
Thu Dec 20 21:04:13 MST 2007
either by it's 10.0.0.2 address, or its local smb (samba) name.
Your config looks to be the same as mine ... what am I missing?
aloha,
dave
On Wed, Apr 14, 2004 at 03:18:32PM -0600, Mike Staver wrote:
> Not sure if this will help, but here is my info from my 678 - note that
> there is a website hosted here, and that I can see it using the dns name
> which points to the outside ip address from the LAN just fine. I have
> also done the same elsewhere using a Cisco 678. One question though,
> since you're using the outside address, do you know that your ISP has
> port 80 open to your IP? I'm not sure if it matters, if a connection
> from the local LAN traverses through your ISPs router or not... just a
> thought.
>
> cbos#sh int
> IP Address Mask
> eth0 192.168.0.1 255.255.255.0
>
> vip0 0.0.0.0 255.255.255.0
>
> vip1 0.0.0.0 255.255.255.0
>
> vip2 0.0.0.0 255.255.255.0
>
> wan0 Physical Port: Trained
>
> Dest IP Address Mask
> wan0-0 216.38.219.1 255.255.255.0
>
> cbos#sho route
> [TARGET] [MASK] [GATEWAY] [M][P] [TYPE] [IF]
> [AGE]
> 0.0.0.0 0.0.0.0 0.0.0.0 1 SA
> WAN0-0 0
> 192.168.0.0 255.255.255.0 0.0.0.0 1 LA ETH0
> 0
> 216.38.219.0 255.255.255.0 0.0.0.0 1 A
> WAN0-0 0
>
> WAN Interfaces...
> 216.38.219.1 255.255.255.0 0.0.0.0 1 HA
> WAN0-0 0
>
> cbos#show nat
>
> NAT is currently enabled
>
> Port Network Global
> eth0 Inside
> wan0-0 Outside 216.38.219.245
> vip0 Outside
> vip1 Outside
> vip2 Outside
>
> Local IP : Port Global IP : Port Timer Flags Proto
> Interface
> 192.168.0.25:143 *****:143 0 0x00041 tcp eth0
> 192.168.0.25:25 *****:25 0 0x00041 tcp
> eth0
> 192.168.0.25:80 *****:80 0 0x00041 tcp
> eth0 wan0-0
> 192.168.0.3:3046 216.38.219.245:18387 86250 0x00046 tcp
> eth0 wan0-0
> 192.168.0.3:3056 216.38.219.245:18391 86310 0x00046 tcp
> eth0 wan0-0
> 192.168.0.3:3064 216.38.219.245:18395 86280 0x00046 tcp
> eth0 wan0-0
> 192.168.0.1:23 216.38.219.245:23 86400 0x0004A tcp
> eth0 wan0-0
> 192.168.0.2:1027 216.38.219.245:18893 60 0x00046 udp
> eth0 wan0-0
>
> Dave Price wrote:
>
> >Hello,
> >
> >I am trying to use port-forwarding with a cisco 678 DSL router.
> >
> >I have a static IP address assigned to the device of 64.65.162.63
> >
> >We are using the device's NAT and onboard DHCP to connect a LAN the
> >Internet. Local devices work fine with addresses in the 10.0.0.0/24
> >range.
> >
> >The device is configured to pass ports 80 (http) and 22 (ssh) on to
> >local IP address 10.0.0.2.
> >
> >I can call up web pages and login via ssh from 'outside' the LAN just
> >fine, but when I am 'inside' I cannot use the 64.65.162.63 address to
> >connect, although the 10.0.0.2 address works fine for http and ssh.
> >
> >Below is the (I think) relevant config info from the 678. Am I mistaken
> >in my belief that the 'outside' address should work the same whether we
> >are inside or out? Any hints as to what I need to change to get this to
> >work right?
> >
> >aloha,
> >dave
> >
> ><paste>
> >
> >cbos#sho int
> > IP Address Mask
> >eth0 10.0.0.1 255.255.255.0
> >vip0 0.0.0.0 255.255.255.0
> >vip1 0.0.0.0 255.255.255.0
> >vip2 0.0.0.0 255.255.255.0
> >wan0 Physical Port: Trained
> >
> > Dest IP Address Mask
> >wan0-0 209.150.192.10 255.255.255.255
> >
> >cbos#sho route
> >[TARGET] [MASK] [GATEWAY] [M][P] [TYPE] [IF]
> >[AGE]
> >0.0.0.0 0.0.0.0 0.0.0.0 1 SA
> >WAN0-0 0
> >10.0.0.0 255.255.255.0 0.0.0.0 1 LA ETH0
> >0
> >209.150.192.0 255.255.255.0 0.0.0.0 1 AR
> >WAN0-0 0
> >
> >WAN Interfaces...
> >209.150.192.10 255.255.255.255 0.0.0.0 1 HA
> >WAN0-0 0
> >
> >IP NAT = enabled
> >IP Multicast Forwarding = disabled
> >IP Port RIP Send Responses = 00, disabled
> >IP Port RIPv2 Send Type = 00, donotsend
> >IP Port RIPv2 Receive Type = 00, donotreceive
> >IP Port RIP Send Responses = 01, disabled
> >IP Port RIPv2 Send Type = 01, donotsend
> >IP Port RIPv2 Receive Type = 01, donotreceive
> >IP NAT Entry = 10.0.0.2, 22, 64.65.162.63, 22, tcp;10.0.0.2, 80,
> >64.65.162.63, 80, tcp;
> >
> >cbos#show nat
> >
> >NAT is currently enabled
> >
> >Port Network Global
> >eth0 Inside
> >wan0-0 Outside 64.65.162.63
> >vip0 Outside
> >vip1 Outside
> >vip2 Outside
> >
> > Local IP : Port Global IP : Port Timer Flags Proto
> >Interface
> > 10.0.0.2:22 64.65.162.63:22 0 0x00041 tcp
> >eth0 wan0-0
> > 10.0.0.2:80 64.65.162.63:80 0 0x00041 tcp
> >eth0 wan0-0
> > 10.0.0.2:631 64.65.162.63:631 90 0x00046 udp
> >eth0 wan0-0
> > 10.0.0.2:42864 64.65.162.63:21505 86340 0x00046 tcp
> >eth0 wan0-0
> > 10.0.0.2:42865 64.65.162.63:21507 86250 0x00046 tcp
> >eth0 wan0-0
> > 10.0.0.5:138 64.65.162.63:21779 30 0x00046 udp
> >eth0 wan0-0
> >
> >cbos#
> ></paste>
> >_______________________________________________
> >CLUE-Tech mailing list
> >Post messages to: CLUE-Tech at clue.denver.co.us
> >Unsubscribe or manage your options:
> >http://clue.denver.co.us/mailman/listinfo/clue-tech
>
> --
>
> -Mike Staver
> staver at fimble.com
> mstaver at globaltaxnetwork.com
> _______________________________________________
> CLUE-Tech mailing list
> Post messages to: CLUE-Tech at clue.denver.co.us
> Unsubscribe or manage your options:
> http://clue.denver.co.us/mailman/listinfo/clue-tech
More information about the clue-tech
mailing list